Why Understanding-Discovering-Knowing Plumbing Basics-Essential Plumbing Skills is Crucial-Important-Essential When Installing-For Installing a Bathtub
Why Understanding-Discovering-Knowing Plumbing Basics-Essential Plumbing Skills is Crucial-Important-Essential When Installing-For Installing a Bathtub
Blog Article
Here below you will discover a bunch of good material in regards to How to Install a Bathtub.
Installing a tub isn't exactly brain surgery, however it does need solid plumbing, woodworking, and also sometimes, tiling skills. Replacing an old bathtub with a new one is also a moderately tough job. If the old tub is readily easily accessible, the job can relocate speedily; if you have to open up a wall surface to get rid of the old tub as well as position the brand-new bath tub, the job is much harder. In either instance, the project is within a home handyman's skills, although you will need an assistant to vacate the old bathtub and also embeded in the brand-new one. Ensure you have actually certified on your own for the job as well as fit trying it. As opposed to hiring a professional to take over a halfway-completed task, it is far better to consider utilizing one before you begin. Opportunities are you might require a specialist plumber to make tube connections.
This short article will assist you set up a brand-new tub in your bathroom if you have already purchased a brand-new tub as well as don't need to change the arrangement of your previous water supply pipelines.
Your tools as well as product list need to comprise the following:
Planning for the Setup
First of all, the sustaining structure provided with the bath needs to be fitted (if needed) according to the supplier's directions. Next, fit the faucets or mixer to the tub. When fitting the faucet block, it is very important to see to it that if the tap comes with a plastic washer, it is fitted in between the bath and also the taps. On a plastic bathroom, it is likewise reasonable to fit a sustaining plate under the taps device to avoid pressure on the bathtub.
Fit the versatile faucet ports to the bottom of both taps making use of 2 nuts and olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet through the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bathroom. See to it you use every one of the provided washing machines.
Attach the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom must currently be ready to be suited its final position.
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your installation, after that the first thing you ought to do is separate the water. After doing so, switch on the taps to drain any water staying in the system. The process of removing the existing taps can be rather problematic because of the limited gain access to that is frequently the case.
Utilize a container wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipes to the taps. Have a fabric all set for the continuing to be water that will certainly originate from the pipes. As soon as the supply pipes have been gotten rid of, make use of the very same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the single faucets from transforming during this process. As soon as the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleaned of any old sealing compound.
Prior to proceeding to fit the new taps, compare the pipeline connections on the old faucets to the new taps. If the old faucets are longer than the brand-new faucets, after that a shank adapter is required for the new taps to fit.
Setting up the Tub
Making use of both wood boards under its feet, place the bathtub in the required placement. The wooden boards are useful in equally spreading the weight of the bathtub over the area of the boards as opposed to focusing all the weight onto four small points.
The next goal is to guarantee that the bath tub is leveled all round. This can be attained by checking the level and adjusting the feet on the bath tub until the spirit level reads degree.
To set up faucets, fit all-time low of the outermost adaptable tap port to the suitable supply pipeline by making a compression join; after that do the same for the other tap.
Turn on the water supply and check all joints and also brand-new pipework for leaks as well as tighten them if essential. Load the bath tub as well as additionally check the overflow electrical outlet as well as the typical outlet for leakages.
Ultimately, repair the bathroom paneling as explained in the manufacturer's user's manual. Tiling as well as securing around the bath tub must wait until the tub has actually been made use of a minimum of once as this will certainly settle it right into its final position.
Suitable New Touches
If the tails of the brand-new faucets are plastic, then you will certainly need a plastic port to stop damages to the thread. One end of the connector fits on the plastic tail of the tap and the other end supplies a link to the existent supply pipelines.
If you need to fit a monobloc, after that you will certainly need lowering couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next off, place the faucet in the mounting hole in the bath/basin guaranteeing that the washers are in area in between the faucet and also the sink. Secure the faucet in place with the manufacturer provided backnut. As soon as the tap is firmly in position, the supply pipes can be attached to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with regular tap connectors. The previous type ought to be attached to the tap ends initially, tightening only by hand. The supply pipes can later be linked to the various other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Bathtub
In the location where the bathroom satisfies the floor tile, it is needed to secure the joins with a silicone rubber caulking. This is very important as the fitting can move sufficient to crack an inflexible seal, creating the water to pass through the wall in between the bath as well as the tiling, resulting in difficulties with wetness and also feasible leakages to the ceiling listed below.
You can pick from a range of coloured sealers to blend in your fixtures as well as fittings. They are sold in tubes and cartridges, and are capable of securing gaps as much as a width of 3mm (1/8 inch). If you have a bigger space to fill up, you can load it with twists of soaked paper or soft rope. Bear in mind to constantly fill the bathtub with water prior to securing, to enable the motion experienced when the bathtub is in use. The sealer can fracture fairly early if you do not consider this motion before sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are likewise easily available on the marketplace. It is a good idea to fit the ceramic tiles utilizing waterproof or water resistant sticky and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a keen person who reads about A Step-by-Step Guide to Installing a Bathtub, I was thinking sharing that information was worth the trouble. Loved our blog entry? Please share it. Help another person check it out. Thanks for going through it.
Book Now Report this page